Technical Reference

Paper Cone Specifications: Dimensions, Taper and Finish

A useful paper cone specification names the taper, length, both inner diameters, finished weight, paper grade and finish. Aziz discusses 4°20′ and 5°57′ families; final dimensions and acceptance limits are agreed against your drawing or sample.

Available paper cone specification ranges

Inner diameters, axial length and paper grade by taper family
Specification4°20′5°57′
Top / nose inner diameter27.5–28.5 mm27–28.5 mm
Bottom / base inner diameter57.5–58.5 mm67.5–68.5 mm
Axial cone length170–173 mm170–173 mm
Paper grade350–450 GSM350–450 GSM

Diameters above are inner diameters (ID). These are available ranges, not manufacturing tolerances or individual batch measurements. Confirm the selected dimensions, measurement positions, finish and tolerances on the approved sample or drawing.

Four paper yarn cones with green, yellow and dark rim markings
Cone examples from our product gallery. Specify rim color and marking separately from dimensions and surface finish.
Close-up of a paper cone's large-end opening and inner wall
The base inner diameter is measured inside the large-end opening. Agree where the measurement is taken; this photograph is not a dimensional inspection record.

Request a sample or quotation

Specification fields for a buyer-approved order

Key Specifications at a Glance

Key specifications at a glance
Taper families 4°20′ / 5°57′
Length (L) 170–173 mm; confirm the order-specific length on the approved drawing
Top / nose inner diameter (d) Small-end internal diameter; agree measurement position and tolerance
Base inner diameter (D) Large-end internal diameter; agree measurement position and tolerance
Finished cone weight Specify finished cone weight per piece; confirm by sample
Paper GSM 350–450 GSM; paper grade is separate from finished cone weight
Surface finish Smooth, Velvet, Embossed
Color and marking Confirm kraft body, rim color and printing requirements per order
Tolerances Agree in writing against the buyer-approved drawing; no universal tolerance is stated
Packaging Confirm pieces per carton, carton dimensions, net/gross weight and packing method with the quotation

L is the end-to-end axial length. d and D refer to the internal openings at the small and large ends. Specify the distance from each rim where a diameter is measured. An outer diameter is a separate value and must not be substituted for an inner diameter.

Request a sample or quotation

4°20′ and 5°57′: use degree-minute notation

The minute symbol means one-sixtieth of a degree: 4°20′ is approximately 4.333°, while 5°57′ is 5.95°. Decimal 4.20° is a different angle. Do not convert an ambiguous order label without checking the buyer’s drawing. Preserve the drawing’s definition of the taper angle as well as its notation.

Selection question4°20′ family5°57′ family
Which machine?Match the exact holder and setupMatch the exact holder and setup
Length and boresAgree for the specific coneAgree for the specific cone
FinishSmooth, velvet or embossed; trial requiredSmooth, velvet or embossed; trial required
Interchangeable?Do not substitute without approvalDo not substitute without approval

See our machine/specification matching guide. No brand-wide fit or single machine speed is promised.

How to measure a reference paper yarn cone

  • Label the reference cone, drawing revision and measurement date. Note storage and conditioning conditions.
  • Measure axial length between the end faces. Avoid measuring along the sloping wall.
  • Use suitable, checked measuring tools for the nose and base bores. Record the internal diameter and its measurement depth. Do not squeeze a paper rim to obtain a reading.
  • Check multiple orientations at each agreed cross-section and record individual readings; agree the roundness method and limits before inspection.
  • Weigh the finished empty cone. Record paper GSM from the agreed material specification separately.
  • Repeat across agreed samples and lots. Keep the individual results and measurement method with the approved reference.

Use the measurement checklist to organize an inquiry. A photograph is not a substitute for a dimensioned drawing or physical reference. We do not publish an unmeasured diagram as production evidence.

GSM, finished weight and finish answer different questions

GSM is paper mass per unit area. Cone weight is the mass of the finished empty cone, including its construction and finishing. They are not interchangeable, and neither figure alone establishes wall strength or winding performance. Ask for the material grade, finished weight and relevant agreed test method.

For the inner wall, inspect for loose fibres, protruding adhesive and damage that could affect seating. For the outside, compare the proposed smooth, velvet or embossed surface using the actual yarn and winding setup. Specify rim color and printing separately from the finish.

Approval and repeat-order control

Agree nominal dimensions, tolerances, sampling method, packing and trial acceptance in writing. Record the approved cone or drawing revision on repeat orders. Request the inspection records required for your order before production; an advertised range is not a batch result.

Procurement and QC teams can use our spinning-mill incoming inspection and ordering guide. For custom specifications, send the drawing and highlight which requirements differ from your existing cone. Availability, MOQ and timing are confirmed during quotation.

Keep a sample and incoming-inspection record

Record the approved drawing revision, measurement positions, individual sample readings and mill-trial outcome. Keep paper GSM separate from finished cone weight, and compare results with the limits agreed for your order.

Download the blank inspection checklist (text)

This is a worksheet for your team to complete, not a test certificate or evidence that a batch has passed inspection.

What you can check before ordering

These are unretouched photographs of our cones, office and factory floor. They show how a cone can be checked and what you can see on a visit. They are not measured results, inspection records or acceptance limits for your order.

A nested stack of finished kraft paper cones standing on a digital scale on an office desk
Process demonstration: weighing a nested stack of finished cones. The reading is for the whole stack on a general-purpose scale, not a per-cone weight or a calibrated result. Agree the finished cone weight, the weighing method and how many cones are weighed for your order.
Seven kraft paper cones of different lengths and rim markings standing side by side
Reference cones with different rim markings and sizes. Send your own reference cone or drawing so the length, both inner diameters and the rim are matched; a photograph alone does not fix the dimensions.
Visitors on the Aziz Packaging factory floor holding finished paper cones beside the production machines
Visitors on our factory floor with finished cones. Buyers can arrange a visit to see production and look at sample cones; call ahead to agree a time.

Before an order you can

  • Send a reference cone, a dimensioned drawing or a photo of your current cone for matching.
  • Receive a sample to measure and to trial on your own winder, with your yarn and settings.
  • Agree in writing which dimensions are measured, where on the cone, with which instrument, on how many cones, and against which limits.
  • Ask for the inspection record format you need with the quotation, and visit the factory by appointment.

Discuss a sample Send a cone photo on WhatsApp

About the manufacturer

Aziz Packaging Limited manufactures kraft paper yarn cones in Narayanganj 1450, Bangladesh, using manual and fully automatic production. Discuss 4°20′ and 5°57′ taper families and smooth, velvet or embossed finishes with our team. Order-specific dimensions, finished cone weight, paper grade, packing and machine suitability are confirmed for the requested specification, subject to buyer sample or drawing approval. Explore the product range or plan an export quotation.

Get a quote faster on WhatsApp

Message your machine model, taper angle, quantity and destination.

WhatsApp us

Prefer to write? Send your requirement below and choose how we reply

Request a Quote

Send what you have: a reference cone, a drawing or the measurements above, with taper (or "Not sure"), finish, quantity and delivery location.

Fields marked * are required. Everything else is optional.

How should we reply?

Our sales team reviews every request and replies by the method you chose. You can also send a cone photo or drawing on WhatsApp.

Related buyer resources